Atlas Copco Authorized Sales and Service Distributor
Service & Maintenance 6 October 2026

How to Adjust the Pressure on a Screw Compressor

How to Adjust the Pressure on a Screw Compressor
In the screw compressor systems used in industrial facilities, setting the pressure correctly plays an important role in both energy efficiency and equipment life. Incorrect pressure settings can cause unnecessary energy consumption and additional load on the system. In this article from Yıldırım Soğutma, we answer the question "How do you adjust the pressure on a screw compressor?" in terms of technical requirements and correct application methods.

What Is Pressure Adjustment on a Screw Compressor and Why Is It Important?

Pressure adjustment on a screw compressor means setting the upper and lower limits of the compressed air the system will produce and distribute to the line. This setting is made to provide the minimum pressure the production line needs while preventing the compressor from running at unnecessarily high pressure. A correctly configured pressure setting allows the screw compressor system to consume less energy, run more evenly and suffer less mechanical wear in the long run. Pressure adjustment is therefore a technical optimization that directly affects system efficiency.

How the Pressure Setting Affects Compressor Performance

On a screw compressor, the working pressure directly determines how long the compressor motor will run under load. Pressure values set higher than necessary make the motor draw more energy and put extra mechanical stress on the screw element. A correctly set pressure, on the other hand, lets the compressor cycle in shorter periods, lowering energy consumption and increasing system stability. In terms of performance, the pressure setting determines not the compressor's capacity but how efficiently that capacity is used.

Risks of an Incorrect Pressure Setting

The most common problems in screw compressor systems with incorrect pressure settings are excessive energy consumption and premature equipment wear. In systems running at high pressure, seals, hoses and fittings can deform faster. With low pressure settings, production lines can suffer performance losses and pressure drops. Compressors that constantly start and stop also increase the risk of faults in the motor and electrical components.

What You Need to Know Before Adjusting the Pressure

Before adjusting the pressure on a screw compressor, the system's current condition and operating conditions should be clearly analyzed. Random adjustments may seem to work in the short term, but they can lead to energy losses and equipment damage in the long run. At this stage, the compressor's capacity, the air line it is connected to, the points of use and the minimum pressure the production process needs should be determined.

Safety Precautions and System Checks

Before starting the pressure adjustment, the screw compressor must be stopped in a controlled way and the pressure in the system reduced to a safe level. The electrical supply should be disconnected and measures taken to prevent unauthorized changes through the control panel. Making adjustments without visually checking compressed air lines, safety valves and connection points can create serious occupational safety risks. Safety checks are therefore the first and indispensable step of pressure adjustment.

Determining the Current Pressure Values

To make a correct adjustment, you need to know exactly what pressure range the system is currently working in. To do this, check the working pressure values on the control panel and, if necessary, take gauge readings at different points on the line. Assessing the loaded and unloaded working pressures separately in particular allows the system's behavior to be read correctly.

How Does Pressure Adjustment Work on a Screw Compressor?

Pressure adjustment on a screw compressor is based on control logic that decides when the system will run under load and when it will run unloaded according to air demand. This process is managed with the load and unload pressure values defined on the compressor's control panel. The aim is to provide the pressure the production line needs without interruption while preventing the compressor from running constantly under load unnecessarily. At the heart of the question "How do you adjust the pressure on a screw compressor?" is striking the right balance between these two pressure values.

What Is Load Pressure?

Load pressure is the pressure level at which the compressor starts producing air again when system pressure falls to the set lower limit. This value should be set taking into account the minimum pressure the production line needs. Setting the load pressure higher than necessary makes the compressor start more often and the motor consume more energy. A correctly set load pressure ensures the screw compressor system runs evenly and prevents sudden pressure drops.

What Is Unload Pressure?

Unload pressure is the pressure level at which the compressor comes off load and stops producing air when system pressure reaches the upper limit. At this stage the motor may keep running, but the screw element does not compress air. An unload pressure set higher than necessary causes excessive pressure in the system and wastes energy. Setting it too low causes frequent load/unload transitions, increasing mechanical wear. The unload pressure should therefore be set carefully so that it is compatible with the load pressure.

How to Adjust the Pressure on a Screw Compressor

The adjustment is made through the compressor's control panel and involves redefining the load and unload pressures according to production needs. When done correctly, energy consumption falls, the system runs more stably and equipment life is extended.

Adjusting the Pressure on the Control Panel

In modern screw compressor systems, pressure settings are made through digital or analog control panels. First, enter authorized access mode and display the current load and unload pressure values. Because changes made on the panel directly affect how the compressor behaves, uninformed changes to the settings menu should be avoided. Panel settings made without clearly defining the required parameters can upset the system's balance.

Steps to Increase or Decrease Pressure Values

When setting pressure values, the minimum pressure the production line needs should be used as the reference. First, the load pressure is set slightly above the lowest acceptable value on the line. Then the unload pressure is set to create a suitable differential with the load pressure. Raising pressure unnecessarily increases energy consumption, while lowering it too much can adversely affect production performance. Each adjustment step should therefore be controlled and based on measurements.

Saving the Settings and Applying Them to the System

Once the pressure settings are complete, the changes must be saved on the control panel and the system brought back online. The compressor should be observed while running loaded and unloaded, and pressure transitions, start frequency and operating noise should be monitored carefully. The data obtained during the first run is critical for confirming that the settings are correct. For a reliable result, the system should not be taken to full capacity after a screw compressor pressure adjustment without a short test.

How Are the Load and Unload Pressure Values Determined?

The main aim when determining load and unload pressure values is to supply the minimum pressure the production line needs without interruption while preventing the compressor from running at unnecessarily high pressure. To do this, the actual pressure measured under load at the furthest point of the line is first taken as the reference. The load pressure is set slightly above this value, and the unload pressure is placed at a reasonable upper limit that keeps the system stable. Too narrow a difference between the two values causes frequent load/unload transitions, while too wide a difference wastes energy.

Points to Watch When Adjusting Pressure

The most common mistake when adjusting pressure is the assumption that "higher pressure = better performance". In fact, unnecessarily increased pressure raises energy consumption and puts extra load on mechanical components. When adjusting, sudden air demands in the production process, possible leaks in the system and the compressor's capacity limits must always be taken into account. Adjustments should also not be one-off but applied gradually based on measurement and observation. For a reliable result, system behavior should be monitored after a screw compressor pressure adjustment and fine-tuned if necessary.

The Right Pressure Setting for Energy Efficiency

In screw compressor systems, every unnecessary 1 bar increase in working pressure can raise energy consumption by about 6–8%. The right pressure setting therefore directly affects not only system performance but also the business's total energy costs. Working at the minimum pressure level the production line needs keeps the compressor under less load and helps the motor run more evenly.

Checks and Testing After Pressure Adjustment

After the pressure adjustment is complete, a controlled test process should be applied instead of immediately running the system at full capacity. The compressor's loaded and unloaded running times should be observed, and pressure transitions and start frequency monitored. Pressure stability should also be confirmed by taking measurements at different points on the air line. These tests show whether the setting is compatible with how the system behaves. For a reliable result, checks after a screw compressor pressure adjustment are as important as the adjustment itself.

Expert Support for Correct Pressure Settings on Screw Compressors

At Yıldırım Soğutma, we take a field-based approach to the effect of correct pressure settings on energy efficiency and equipment life in screw compressor systems. With our experienced technical team and 24/7 service infrastructure, we reliably set the pressure your compressor needs. Contact us to optimize screw compressor performance and learn about the right solutions.

Frequently Asked Questions

How do you adjust the pressure on a screw compressor?

Screw compressor pressure is adjusted by redefining the load and unload pressure values on the control panel according to the needs of the production line. Current pressure values should be measured before the adjustment, and the system should be tested under load afterwards. For a reliable result, the process should be applied gradually.

Is the pressure adjusted from the control panel?

Yes. In modern screw compressor systems, pressure settings are made through digital or analog control panels. Because the parameters on the panel directly affect how the compressor behaves, they should only be changed by authorized, knowledgeable people.

How many bar should the load and unload pressures be?

These values are not fixed; they are determined by the facility's air needs. In general, a difference of 0.5–1.5 bar between the load and unload pressures is recommended. However, the ideal range should be determined taking into account the production line's minimum pressure requirement and system losses.

Does lowering the pressure setting save energy?

Yes. Systems running at unnecessarily high pressure cause serious energy losses. Lowering the pressure setting to a level that matches production needs reduces the screw compressor's energy consumption and saves on operating costs.

Does an incorrect pressure setting damage the compressor?

An incorrect pressure setting can overload the motor, cause premature wear in the screw element and mechanical wear due to frequent starting and stopping. In the long run, this can lead to serious breakdowns and high maintenance costs.

Is testing necessary after adjusting the pressure?

Yes. After the adjustment, the compressor's loaded and unloaded running times should be monitored, pressure transitions checked and system stability confirmed. Settings made without testing should not be assumed to give the right result.

Is the adjustment method the same on every screw compressor?

Although the basic logic is the same, the control panel interface, software structure and settings menus can differ by brand and model. For each screw compressor, the manufacturer's documentation should therefore be consulted and the adjustment made accordingly.

Are pressure fluctuations caused by incorrect settings?

Pressure fluctuations are often caused by incorrect settings, leaks in the line or insufficient air capacity. However, one of the first things to check is whether the load and unload pressure values have been defined correctly.