Atlas Copco Authorized Sales and Service Distributor
Service & Maintenance 6 October 2026

Chiller Fault Codes: The Most Common Errors and What They Mean

Chiller Fault Codes: The Most Common Errors and What They Mean
Faults in chiller systems matter a great deal to businesses, because they can suddenly stop many critical lines, from production to process cooling. Correctly interpreting chiller fault codes, chiller alarm codes and the warnings most often seen in the field, such as high pressure fault and low pressure fault, therefore reduces downtime and extends equipment life. In this article, we explain in plain, simple terms what the codes that look complicated at first glance really point to when industrial chiller faults occur, helping you decide on the right action faster.

High Pressure Fault (HP)

A high pressure fault (HP) occurs when the condensing pressure in the chiller circuit exceeds the manufacturer's limits, causing the unit to stop automatically for safety. On the chiller control panel it usually appears as "high pressure fault", "HP alarm" or a similar code.

This fault arises from causes such as the condenser not rejecting enough heat, fans running at low speed, reduced cooling water flow, fouled condenser surfaces, too much refrigerant in the system or pressure sensors giving false readings. As pressure rises, the compressor strains, energy consumption increases and there is a risk of serious damage to the system. The HP alarm is therefore not just a warning but the chiller's self-protection reflex.

Low Pressure Fault (LP)

A low pressure fault (LP) occurs when the pressure in the chiller's evaporator circuit drops below the normal operating level, causing the system to stop for safety. On the control screen it is usually shown as "low pressure fault" or "LP alarm". It can be triggered by many technical causes, such as a lack of refrigerant, icing on the evaporator surfaces, low water flow, clogged filters, pump problems or a faulty pressure sensor. An excessive drop in pressure poses a serious risk to the equipment because it upsets the compressor's lubrication balance.

Flow Fault – No Water Circulation

A flow fault occurs when the water circulation the chiller needs to run is interrupted or the sensor cannot detect sufficient flow. On the control panel it usually appears as "Flow Fault", "No Water Flow" or "Flow Switch Alarm". This warning is triggered by causes such as the pump not running, an air lock in the line, a clogged filter or heat exchanger, closed valves, a low water level or a faulty flow switch.

Because there is no water flow, the evaporator cannot give up its heat, making this both a common cause of downtime among industrial chiller faults and a safety lock that protects the equipment. Forcing the system to run without fixing the flow fault can lead to icing in the evaporator and serious compressor failures, so it requires fast and correct action.

Water Temperature Sensor Fault

A water temperature sensor fault, occurs when the sensors measuring the chiller's inlet or outlet water temperature send false, inconsistent or unreadable values. On the control panel it is usually shown as "chiller sensor fault", "Water Temp Sensor Error" or "Temperature Fault".

This fault is triggered by causes such as broken sensor cables, oxidation, loose connections, physical damage to the sensor, incorrect placement, calibration drift or an error in the reading circuit on the control board. Temperature sensors are critical for the chiller's capacity modulation and among chiller fault codes, because if the system cannot read the water temperature correctly, the compressor's running time, defrost cycle and safety limits cannot be managed properly.

A Temperature Sensor Fault is therefore not just a reading problem but an important alarm that affects both energy efficiency and equipment safety. Sensor values that look inconsistent, very low or abnormally high are usually the first sign that a component needs replacing or the cable line needs checking again.

Anti-Freeze Alarm

The anti-freeze alarm is a safety warning that is activated when the water temperature in the evaporator circuit drops critically and approaches the risk of freezing. This alarm stops the system automatically to protect both the chiller's heat exchanger and the circuit components. On the control screen it is usually shown as "Anti-Freeze", "Freeze Protection", "Low Leaving Water Temp" or similar.

It can be triggered by causes such as insufficient water flow, clogged filters, low flow faults, excessively low setpoints, false temperature sensor fault readings or an insufficient glycol ratio in the system. When the water temperature approaches freezing point, ice forms on the evaporator surface, and this ice can quickly block the flow path, leading to a chiller low pressure fault and then a serious chain of faults extending to mechanical damage to the compressor.

Condenser Temperature Fault

A condenser temperature fault is a critical warning that appears when the temperature in the chiller's condensing circuit rises above normal operating limits. On the control panel it is usually shown as "Condenser Temp Fault", "High Condenser Temperature" or "Discharge Temp Alarm". This fault is triggered by not enough air or water reaching the condenser, fans running at low speed, fouled condenser surfaces, high ambient temperature, too much refrigerant or sensor faults.

When the condenser overheats, the system cannot reject heat to the outside, leading directly to a chiller high pressure alarm and even compressor overload. High condenser temperature is one of the most critical parameters, increasing energy consumption, reducing capacity and shortening equipment life. When a condenser temperature fault appears, both the air/water flow conditions and the overall pressure balance of the cooling circuit must therefore be checked in detail.

Compressor Fault / Overload

A compressor fault / overload is one of the most critical causes of chiller downtime and occurs when circuit protection trips because the compressor's workload exceeds its limits. On the control panel it usually appears as "Compressor Overload", "Comp. Fault", "Motor Protection" or "Overcurrent Alarm".

It can result from many causes, such as high pressure conditions (high pressure fault), low pressure problems (low pressure fault), insufficient lubrication, mechanical seizure, excessive current draw, fan failures, refrigerant imbalance, fouled heat exchangers or electrical contactor/thermal relay problems. When the compressor is overloaded, the motor windings heat up, current values rise and the protection circuit shuts the system down to prevent greater damage.

An overload fault is also a warning of chain faults; for example, false sensor readings (chiller sensor fault), insufficient water flow or condenser temperature problems can also increase the compressor's load and cause this alarm to recur. A compressor fault should therefore be seen not just as an electrical problem but as a need for a comprehensive check affecting the performance of the whole cooling circuit.

Fan Motor Error

A fan motor error, is a fault that occurs when one or more of the chiller's condenser fans do not run at the required speed, do not start at all or send incorrect feedback to the control board. On the control screen it usually appears as "Fan Motor Error", "Fan Fault", "Fan Overload" or "Fan Speed Error".

This fault can be triggered by a burnt-out fan motor, capacitor failure, seized bearings, unbalanced fan blades, inverter/speed controller problems or wiring problems. Because fans that do not run efficiently make it harder for the condenser to reject heat, they can lead directly to a chiller high pressure alarm, high condenser temperature faults and compressor overload.

PLC / Control Board Faults

PLC / control board faults, are software or hardware problems in the automation brain that manages all of the chiller's operating logic, and they are often considered more critical than other faults. On the control panel they appear with codes such as "PLC Fault", "Control Board Error", "Communication Fail", "I/O Error" or similar.

They can be triggered by burnt components on the control board, power supply imbalances, loose terminal connections, false signals from sensors (chiller sensor fault), software conflicts, module communication interruptions or the CPU on the board freezing. When PLC faults occur, the chiller may give wrong commands, fan or compressor timing may be disrupted, and alarms in the field such as high pressure fault and low pressure fault can no longer be interpreted correctly.

Chiller Reset Steps

Chiller reset steps clear the unit's fault memory and return it to safe operating mode, but if not carried out correctly they can lead to the fault recurring or to greater damage. A reset should therefore only be carried out after the root cause of the fault has been fixed. A typical chiller reset goes as follows:

  1. Switch off the chiller and disconnect the power supply.

    The unit is completely de-energized at the main switch. This step is needed for the PLC and safety circuits to reset themselves.

  2. Check the fault code and make sure the cause has been fixed.

    Do not reset until the chiller fault code or related alarm shown on the screen (for example high pressure fault, low pressure fault, chiller sensor fault) has been dealt with.

  3. Verify the flow, pressure, temperature and sensor values.

    Water circulation, pressure sensors, temperature sensors and current values should have returned to normal levels.

  4. Restore power and switch the unit on.

    Once power is applied, the unit's control board restarts.

  5. Use the Reset button on the control panel.

    Most systems have a physical or digital Reset option on the panel. This clears the alarm memory.

  6. Monitor the system's start-up.

    Follow the start-up sequence of the compressor, fans and pumps and watch whether a new alarm occurs.

If the alarm recurs after the reset, this usually shows that the underlying problem has not been fully solved and the system needs a detailed technical inspection.

Expert Technical Support from Yıldırım Soğutma

Although correctly interpreting chiller fault codes prevents many problems, frequently recurring high pressure faults, low pressure faults, sensor errors or flow problems in particular require a professional technical inspection.

At Yıldırım Soğutma, we keep businesses running without interruption with on-site maintenance, 24/7 service support and genuine spare parts for industrial cooling systems.

To take a closer look at the equipment we use, you can visit our industrial cooling units page, and if you are planning a new investment, our article "What to Consider When Buying a Chiller (2025 Industrial Cooling Guide)" gives comprehensive information about the selection process.

Contact us to request technical service or for information about chiller maintenance service.